Clover Technologies Group LCD26164 Instruction Manual

1INSTRUCTION MANUAL 26” Wide LCD Screen All in One System Built-in 16Ch DVR MODEL: LCD26164, LCD26168, LCD261616 Ver. 041309, 102609 Cop

Stand-alone DVR Instruction Manual 10

Stand-alone DVR Instruction Manual 100 7-5. AUDIO ▫ Click on the AUDIO button in the SETUP menu and then the AUDIO menu will be displayed on the

7. Setup 101 7-6. RECORD ▫ Click the “RECORD” button in the SETUP menu and then the RECORD menu will be displayed as shown in Fig.7-54. ▫ Click th

Stand-alone DVR Instruction Manual 102 7-6.2. All Manual / Timer recording button ▫ Click the All Manual / Timer recording button in the RECORD menu

7. Setup 103 7-6.3. All Motion ON / OFF, Sensitivity Setting ▫ Click the button in the RECORD menu, then the ALL MOTION setup pop-up window will be

Stand-alone DVR Instruction Manual 104 7-6.4. All Sensors ON / OFF ▫ Click the button in the RECORD menu, then the ALL SENSOR setup pop-up window

7. Setup 105 [Fig.7-64 Record Size pop-up window] 7-6.6. Recording Speed ▫ Click the F/S (Frames Per Seconds: Recording Speed) button on each of th

Stand-alone DVR Instruction Manual 106 30 25 15 12 10 8 7 6 5 5 3 3 2 2 1 1 NTSC OFF PAL OFF 7-6.7. Recording Quality ▫ Click the QUALI

7. Setup 107 7-6.8. Recording Mode The factory default setting for Recording is the Manual Recording (or called Continuous Recording), which keeps re

Stand-alone DVR Instruction Manual 108 7-6.9. Recording by Motion Detection When the menu of motion is properly set up (See section 7-6.3 for all

7. Setup 109 ▫ Pre-Alarm Time Setup Allows you to record a section of video just prior to Motion or Sensor activation. Click the mouse on the PRE in

11 1.Unpacking Care should be taken when unpacking to avoid damaging the system. Please check that the following items are included:

Stand-alone DVR Instruction Manual 110 ▫ Region The Motion Detection Area displays in blue on the screen, and it turns to doubly-boxes when the moti

7. Setup 111 By All Set Right-click on the setting window for Motion Detection Area (Fig.7-75), and then the pop-up setting window for Motion Detecti

Stand-alone DVR Instruction Manual 112 - All Clear Right-click on the setting window for Motion Detection Area (Fig.7-75), and then the pop-up setti

7. Setup 113 By Window Set Right-click on the setting window for Motion Detection Area (Fig.7-75), and then the pop-up setting window for Motion Dete

Stand-alone DVR Instruction Manual 114 - Window Clear Right-click on the setting window for Motion Detection Area (Fig.7-75), and then the pop-up se

7. Setup 115 By Each Cell Right-click on the setting window for Motion Detection Area (Fig.7-75), and then the pop-up setting window for Motion Detec

Stand-alone DVR Instruction Manual 116Note : Please pay attention to the following directions in order to use the Motion Detection function prope

7. Setup 117 7-6.10. Recording by Sensor (PIR Sensor) ▫ Click the mouse on the button for each of the channels in the RECORD menu, and then the S

Stand-alone DVR Instruction Manual 118▫ Pre-Alarm Time Setup Allows you to record a section of video just prior to Sensor activation. Click the mous

7. Setup 119 7-7. NETWORK ▫ Click the “NETWORK” button in the SETUP menu, and then the NETWORK menu will be displayed on the screen as shown in Fi

Stand-alone DVR Instruction Manual 12 1-1. 26” Wide LCD Panel Built-in 16 Ch Digital Video Recorder LCD26164 is the most reliable and functional

Stand-alone DVR Instruction Manual 120 7-7.2. GATEWAY, SUBNET, IP ADDRESS ▫ Click the GATEWAY / SUBNET / IP ADDRESS button in the STATIC IP MODE

7. Setup 121 7-7.3. Port ▫ PORT is the TCP address of the program, which is used to connect to the network viewer. It can be set from 1 to 65535 val

Stand-alone DVR Instruction Manual 122 7-7.5. MNS (MAC NAME SERVER) As a sort of DDNS, two servers in our company are being operated so that our cli

7. Setup 123 ▫ IP ADDRESS / PORT DO NOT CHANGE THE IP ADDRESS AND PORT NUMBER IN THE MNS MENU IF YOU DON’T HAVE ANY SPECIAL SERVER TO ACCESS YOUR DVR

Stand-alone DVR Instruction Manual 124 ▫ SERVER - Choose the SERVER button in the DDNS menu by clicking the mouse or pressing the buttons on the rem

7. Setup 125 7-7.7. HOW TO SETUP AND USE THE DDNS 7-7.7.1. Router. It has to be set as a virtual server (or port forwarding) in order to utilize the

Stand-alone DVR Instruction Manual 126 7-7.8. EMAIL NOTIFICATION ▫ Email notification enables to notify events (sensor, motion, video loss, power on

7. Setup 127 ▫ EMAIL ADDRESS SETUP - Click one of email address boxes and then the On Screen Keyboard will show up as shown Fig.7-105. - Delete

Stand-alone DVR Instruction Manual 128▫ EVENT Setup - Click the check boxes below to choose the events you need. - To delete, click the check box ag

7. Setup 129 Note : If the motion is selected in Fig.7-108, you may receive numerous emails from the DVR systems due to a couple of factors such as

13 2.Features ▶ 26” Wide Screen - High resolution TFT-LCD 1,366(H) x 768(V), Contrast ratio 700:1, Response time 8 msec ▶ Multi Functional Rec

Stand-alone DVR Instruction Manual 130

131 8.Remote Host Program 8

Stand-alone DVR Instruction Manual 132 CONTENTS 8-1. REMOTE PROGRAM OVERVIEW ...

133 8-1. Remote Program Overview The Remote Host Program allows you to view live video, search archived video, control PTZ cameras and to set u

Stand-alone DVR Instruction Manual 134 8-2. Installing the Program to PC Install the program into PC by using program CD (supplied) as follows. How

135 8-3. Internet Explorer When you are trying to use this function, it is highly recommended that the password should be turned ON in the SYSTEM m

Stand-alone DVR Instruction Manual 136[Fig.8-3 DVR Master- Windows Internet Explorer] • Click on the following message. This site wants to install

137 8-4. Remote Host [Fig 8-5. DVR Master] ○12 ⑧⑨⑩ ○16 ○13 ○14 ○15 ④ ⑥ ⑤ ⑦ ① ② ③ ⑪

Stand-alone DVR Instruction Manual 138 Table. Description of Remote Host Program Button ① Minimization Button ② Close Button ③ Current Time ④ Conne

139 8-4.1. Setup ① Version number It represents the current version number of the Firmware. ② Copy Refer to Section 8-4.10 in regards to

Stand-alone DVR Instruction Manual 14

Stand-alone DVR Instruction Manual 140 ③ Network Image ▫ Size Choose a Size (Resolution) among D1, Half D1 and CIF you wish to display on the DV

141 [Fig.8-7 Firmware Files]

Stand-alone DVR Instruction Manual 142 8-4.2. Connection There are two ways to access the DVR through the DVR Master as follows. ▫ With Set Direct s

143- Choose a Domain Name in the Name Lists and then click the “CONNECT” button in order to access the DVR. - To register the Domain name (Hos

Stand-alone DVR Instruction Manual 144 8-4.4. Status If the Status button on the DvrMaster is selected by clicking the mouse, the DvrMaster dis

145 8-4.5. Replay It is possible to replay the recorded data from the DVR system by using the Replay button in Fig.8-10 in the Multi mode only

Stand-alone DVR Instruction Manual 146 ▫ Playback Control Playback control buttons : Button for fast rewinding up to 128 times

147 8-4.6. COPY It is possible to copy the recorded data from the DVR system to a client PC by using the Copy button in Fig.8-13 in the Multi mod

Stand-alone DVR Instruction Manual 148 “ALL” in yellow represents that all the cameras are selected. The camera channel number(s) in yellow repr

149 8-4.7. Switch the Normal Screen to Full Screen ▫ Click the “FULL SCREEN” button on the DvrMaster as shown Fig.8-16 and the current screen siz

15 3.What to do at the time of Installation The system should be installed in the following order; 1. Make sure all the required hardware is a

Stand-alone DVR Instruction Manual 150 8-4.8. Speaker / Microphone Buttons of Remote Host Program ① Audio Input channel selection: Select the sa

151 8-4.9. Connection mode There are two kinds of connection mode (See Fig.8-19) on the DvrMaster. Select one of them by clicking the mouse dependin

Stand-alone DVR Instruction Manual 152 8-4.9.2. Multi mode It is impossible to control (Recording on/off, Setup, System Status, Display and OSD) the

153 8-4.10. Copy in the Terminal mode There are four icons such as NETWORK, USB, CD and DVD in the COPY menu of the Multi mode. The recorded data wi

Stand-alone DVR Instruction Manual 154 [Fig.8-22 Copying in the Terminal mode] [Fig.8-23 Copy Completion]

155 8-4.11 E-Map E-Map enables users to display the cameras on the digital map for better monitoring. The digital map should be a BMP file and

Stand-alone DVR Instruction Manual 156 - To rename, right-click a saved eMap list and click “Rename” on the pop-up window as shown in Fig.8-27. - To

157 8-4.11.3. Usage of camera position The small squares with channel numbers on the map indicate the camera position. The blue screen represents th

Stand-alone DVR Instruction Manual 158 8-4.12 Pan / Tilt & Preset You can control the PTZ camera through DvrMaster. This feature is basically

159 8-5. PLAYER [Fig.8-33 Player] Chart. Button of Player Program ① Status window (Play mode, Date, Time) ② Calendar ③ Search button for r

Stand-alone DVR Instruction Manual 16

Stand-alone DVR Instruction Manual 160① Status window (Play mode, Date, Time) It indicates the play mode, date and time. ② Calendar It

161- Click the Convert AVI button on the Player and the Convert AVI window will be displayed (See Fig.8-36. - Click on the SELECT button for Sou

Stand-alone DVR Instruction Manual 162 [Fig.8-39 Select one of the Channels] [Fig.8-40 Start Convert Button] How to p

163⑤ Configuration [Fig.8-41 Configuration window] - If the “Fit to window” is selected in Fig.8-41, it will automatically fit to the Player windo

Stand-alone DVR Instruction Manual 164 ⑧ Video Enhance Refer to section 6-8 on page 53. ⑨ Division button Select one of th

165 ⑪ Search slider for replaying The slider can be moved left and right by clicking the slider on the bar and dragging it or just click the bar

Stand-alone DVR Instruction Manual 166

167 APPENDIX CONTENTS RECORDING TIME TABLE ...

Stand-alone DVR Instruction Manual 168 Recording time table HDD : 750GB , Based on 16 cameras Recording Resolution : CIF(360 X 240)

169 Factory default settings (1) LIVE SCREEN 16 SPLIT OSD ON (2) TIME / DATE DISPLAY : ON TIME FORMAT : 24 HOUR DATE FORMAT : YYYY/MM/D

17 4.Specifications ITEM DESCRIPTIONS Television System NTSC PAL Refresh Rate 60 fields/sec 50 fields/sec Video

Stand-alone DVR Instruction Manual 170SEQ DISPLAY DWELL : 1 SEC (8) AUDIO AUDIO 1 : RELATED CAMERA CH 1, RECORD OFF, LEVEL 5 AUDIO 2 : RELATED CAME

171PRE : 1 sec. HOLD : 1 sec. SPOT : OFF (10) NETWORK TYPE : DYNAMIC PORT : 113 SERVER 1 MODE : DISABLE SERVER 1 IP ADDRESS : 65.60.84.25 SERVE

Stand-alone DVR Instruction Manual 172

173 FAQ CONTENTS I CANNOT LOGIN ...

Stand-alone DVR Instruction Manual 174 I can not login ▶ Please check if the link LED of DVR and LAN port of PC are lit. ▶ Please check if the I

175 Limited 1Year Warranty This warranty gives the original purchaser specific legal rights and you may also have other rights, which may vary from

Stand-alone DVR Instruction Manual 176 How to obtain Factory Service • Original purchaser must fill out the warranty card and mail it to the factor

Stand-alone DVR Instruction Manual 18Display 26” TFT LCD active matrix Pixel Pitch 0.4215 mm Active Display Area 575.76(H) x 323.71(V) mm Display

19 5.Installation CONTENTS 5-1. CONTROLS AND CONNECTORS...

2

Stand-alone DVR Instruction Manual 20 5-1. Controls and Connectors z Front [Fig. 5-1 Front/Side View] POWER LED 8

5. Installation 211. REC Key - Press this key to start recording. - In order to stop recording, press this key again or click the REC button on t

Stand-alone DVR Instruction Manual 22z Rear [Fig 5-2 Rear View] POWER INPUT & POWER SWITCH CAMERA INEACH 12VDC. MA

5. Installation 23 5-2. Note for Installation  Install the system according to the instructions described in this manual.  The 26” LCD monitor

Stand-alone DVR Instruction Manual 24 5-3. System Connection [Fig 5-3 System Connection]

5. Installation 25 5-4. Installation 5-4.1. Camera Connection ▫ Connection of 6pin MINI DIN Cameras Connect the supplied cameras to the Camera

Stand-alone DVR Instruction Manual 26 5-4.2.1. Connection of Composite Monitor If necessary, connect the composite Video Output (yellow RCA) and

5. Installation 27 5-4.4. RS485 Connection ▫ Connect the cable to the “RS485 PORT” on the terminal block of the system. Refer to [Fig 5-7] for conn

Stand-alone DVR Instruction Manual 28CAMERA INEACH 12VDC. MAX 0.25A. 3WCH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8SLAVEV / O A / OETHERNET12345678GAL

29 6. How to operate CONTENTS 6-1. GENERAL INFORMATION...

Contents 3CONTENTS ABOUT THIS MANUAL...

Stand-alone DVR Instruction Manual 30CONTENTS 6-7.4. LIVE AUDIO ...

6. How to Operate 31 6-1. General Information ▫ You can operate all functions of the system by use of the buttons located on the side panel, remote

Stand-alone DVR Instruction Manual 32 6-2. Operating Interface There are 3 ways to operate the system by pressing the buttons on the side panel o

6. How to Operate 33 6-3. IR Remote Controller 1. POWER / STANDBY 2. REC 3. STATUS 4. ZOOM 5. FREEZE 6. No.1~16 Channel (Full Scr

Stand-alone DVR Instruction Manual 34 6-4. Power On/Off 6-4.1. POWER ON On the rear panel: Turn on the POWER switch on the rear panel (See Fig.5-2)

6. How to Operate 35▫ Press the ENTER (↵) button to turn the power OFF. By clicking the mouse: ▫ Right-click on the screen in the live mode to disp

Stand-alone DVR Instruction Manual 36 6-5. Menu Window Right-click on the screen in the LIVE or the RECORD mode and then the MENU window will be

6. How to Operate 37 6-6. Display Screen 6-6.1. FULL SCREEN [Fig.6-5 FULL screen] RECORD ICON CURRENT TIME AUDIO ICON COPY ICON SEQUEN

Stand-alone DVR Instruction Manual 38 6-6.2. SPLIT SCREENS FULL SCREEN QUAD SCREEN SEQUENCING SCREEN 16 SPLIT S

6. How to Operate 39 6-7. LIVE 6-7.1. FULL SCREEN ▫ A Full SCREEN is available in the LIVE mode or the RECORD mode. ▫ Click on a certain camera’s

Stand-alone DVR Instruction Manual 46-6.1. FULL SCREEN...

Stand-alone DVR Instruction Manual 40 6-7.3. SEQUENCING SCREENS ▫ Displaying the cameras in SEQUENCE is available in the LIVE mode or the RECORD mod

6. How to Operate 41 6-7.4. LIVE AUDIO ▫ Setup LIVE AUDIO when the system is not connected through the DvrMaster or Internet Explorer and the OSD is

Stand-alone DVR Instruction Manual 426-7.4.1. COMMUNICATION BETWEEN MONITOR AND CLIENT COMPUTER VIA INTERNET ▫ This system is normally in listeni

6. How to Operate 43 6-7.5. ZOOM The image on the screen will be zoomed up to 2 times when the ZOOM button is clicked in the LIVE mode (This functio

Stand-alone DVR Instruction Manual 44 6-7.6. OSD ON / OFF OSD ON /OFF is possible in the LIVE mode or RECORD mode. ▫ Click the OSD button on the MEN

6. How to Operate 45 6-7.7. PAN / TILT ▫ Click the PAN/TILT button on the MENU window in the LIVE mode to access the PAN/TILT cameras. ▫ Click the

Stand-alone DVR Instruction Manual 46 ▫ Channel Selection and Screen Conversion To change a channel, press the CHANNEL button on

6. How to Operate 47▫ PRESET It is a function to preset the PTZ camera(s) which you wish to monitor frequently. Preset Setup - Select a position

Stand-alone DVR Instruction Manual 48 6-7.8. SYSTEM STATUS ▫ Click the SYSTEM STATUS button on the MENU window to see the system status as shown b

6. How to Operate 49 6-7.9. POWER LOSS LISTS The list indicates the time/date when the system power is turned OFF. ▫ Click the POWER LOSS LISTS but

Contents 56-11. COPY ... 6

Stand-alone DVR Instruction Manual 50 ▫ CLEAR LISTS button Click the CLEAR LISTS button to clear the lists, you will be prompted to confirm change

6. How to Operate 51 6-7.10. VIDEO LOSS LIST The list indicates the video loss channel and the time/date when the video signal is disconnected. ▫ Cli

Stand-alone DVR Instruction Manual 52 ▫ CLEAR LISTS button Click the CLEAR LISTS button to clear the lists, you will be prompted to confirm changes.

6. How to Operate 53 6-8. VIDEO ENHANCE ▫ Click the DISPLAY button in the MENU window to enhance the picture quality on each of channels (Contrast

Stand-alone DVR Instruction Manual 54 6-8.1. CAMERA INPUT CONFIG (CONTRAST / BRIGHTNESS) ▫ Click a CAMERA INPUT button in the VIDEO ENHANCE menu.

6. How to Operate 55 6-8.2. VGA OUTPUT CONFIG (SCALE / CONTRAST / BRIGHTNESS / SATURATION) ▫ To Setup the SCALE / CONTRAST / BRIGHTNESS / SATURATION

Stand-alone DVR Instruction Manual 56 6-9. Record This system provides Watchdog function. When power goes off during recording and the power turns

6. How to Operate 57 The MOTION () or SENSOR ( ) as shown in Fig.6-29 should be turned ON in this recording mode. ▫ Press the RECORD button on the

Stand-alone DVR Instruction Manual 586-9.4. Timer Event Recording ▫ Click the SETUP icon on the MENU window in the LIVE mode. ▫ Click the RECORD

6. How to Operate 59 [Fig.6-33 Hour/Minute Selection Table] 6-9.5 Audio Recording ▫ Click the Audio Recording button, or in the RECORD menu

Stand-alone DVR Instruction Manual 67-6. RECORD...

Stand-alone DVR Instruction Manual 606-9.7. Recording Icons The Recording Icons depends on recording modes are displayed in the upper left hand corn

6. How to Operate 61 6-10. REPLAY 6-10.1. QUICK REPLAY It is available only by pressing the QICK SEARCH button on the remote controller. ▫ Press

Stand-alone DVR Instruction Manual 626-10.2.1. Playback Devices In order to payback, plug the USB devices such as external USB HDD, USB memory to th

6. How to Operate 63▫ Select the hour on the Start Time Select Window (See Fig.6-40) by clicking the mouse on the Hour (0 – 23 hour) you wish to sta

Stand-alone DVR Instruction Manual 64 6-10.2.3. Replaying Replaying start time set-up can be possible within a recording time extent. ▫ Replay butt

6. How to Operate 65▫ How to control the buttons while replaying ① Search Slider It is possible to playback by clicking the slider on

Stand-alone DVR Instruction Manual 66 ⑤ Speaker ON / OFF Turn speaker ON or OFF . ⑥ Speaker Volume Adjust the Audio Volume by clicking the ▲ or t

6. How to Operate 67 - Click the mouse on one out of channels during replaying to view a full screen. - Click the mouse on the full screen during r

Stand-alone DVR Instruction Manual 68 6-11. COPY ▫ Click the COPY icon on the MENU window, and the COPY window as shown in Fig.6-46 will be disp

6. How to Operate 69 ▫ Connect the USB devices to the DVR ▫ Click the SETUP icon on the MENU window, and the SETUP menu will be displayed. ▫ Click

Contents 78-4.2. Connection ...

Stand-alone DVR Instruction Manual 70 ① All channels, HOUR selection button. Click the arrow button in the upper left corner as s

6. How to Operate 71 By using the Start/End set-up bar: The starting time to copy can also be set by clicking the slider on the bar and draggi

Stand-alone DVR Instruction Manual 72 6-11.4. Copying the recorded data during replaying The system, LCD26164 allows users to copy the recorded da

6. How to Operate 73 ▫ Choose one among NETWORK, USB, CD and DVD which are ready to copy (See section 6-11.1). Select COPY Mode

Stand-alone DVR Instruction Manual 74▫ As soon as one of the above buttons is clicked, copying will start along with displaying the icon shown in

75 7. SETUP 7 CONTENTS 7-1. SETUP ...

Stand-alone DVR Instruction Manual 76CONTENTS 7-4. CAMERA ...

7. Setup 77CONTENTS 7-7. NETWORK ...

Stand-alone DVR Instruction Manual 78 7-1. SETUP It is possible to set up the menus in the LIVE mode and partly in the RECORD mode.

7. Setup 79 7-2. SYSTEM ▫ Click the “SYSTEM” button in the SETUP menu, and the SYSTEM menu shown in Fig.7-3 will be displayed. ▫ Click the “EXIT”

Stand-alone DVR Instruction Manual 8

Stand-alone DVR Instruction Manual 80 7-2.1. SYSTEM NAME ▫ Click the “SYSTEM NAME” button in the SYSTEM menu, then the On Screen Keyboard will displ

7. Setup 81 7-2.2. LANGUAGE ▫ Click the “LANGUAGE” button in the SYSTEM menu, then the LANGUAGE submenu will display. ▫ Click one of Languages among

Stand-alone DVR Instruction Manual 82hour/minute/second selection table by clicking the mouse. ▫ DATE FORMAT There are three formats to display t

7. Setup 83 7-2.4. SYSTEM CONFIG ▫ Click the “SYSTEM CONFIG” button in the SYSTEM menu, and then the SYSTEM CONFIG menu will be displayed (See Fig.

Stand-alone DVR Instruction Manual 84 7-2.4.1. FACTORY DEFAULT ▫ Click the “FACTORY DEFAULT” button in the SYSTEM CONFIG menu, and you will be asked

7. Setup 85 7-2.4.2. LOAD CONFIG / BACKUP CONFIG You can save up to four different settings in the BACKUP CONFIG and load the files in the LOAD CONFI

Stand-alone DVR Instruction Manual 86 ▫ BACKUP CONFIG This function is to save the current settings to load the settings to the system. Save the cur

7. Setup 87 7-2.5. PASSWORD ▫ ON/OFF Select ON or OFF by clicking the mouse. If the ON is selected, the password has to be entered to get into the

Stand-alone DVR Instruction Manual 887-2.6. IR REMOTE ID Up to 16 DVR systems can be controlled by only one remote controller we provided, but IDs

7. Setup 89 7-2.7. FIRMWARE UPDATE There are two ways to update the firmware through USB memory and the DvrMaster (GUI). We recommend users to update

9About this manual This is the Instruction Manual for 26” Wide TFT-LCD monitor built-in 16Ch DVR system, Model LCD26164, LCD26168 and LCD261

Stand-alone DVR Instruction Manual 90 7-3. DISK MANAGER ▫ Click the “ ” button in the SETUP menu and the DISK MANAGER window will be displayed (See

7. Setup 91 7-3.1. HDD WRITE FAIL If HDD is in full and the OVERWRITE on the HDD is turned OFF in the recording mode, the system will activate the re

Stand-alone DVR Instruction Manual 927-4. CAMERA ▫ Click the “CAMERA” button in the SETUP menu and the CAMERA menu will be displayed (See Fig.7-29)

7. Setup 93 7-4.1. Camera ON/OFF ▫ Click on each of the channels to select the “O” or “X” in the CAMERA menu. If the “O” is selected, the correspondi

Stand-alone DVR Instruction Manual 94 7-4.3. Buzzer In order to alert users, the Buzzer will sound at that time video signal lost. ▫ Click on each

7. Setup 95 7-4.5. Pan/Tilt Settings ▫ Click the PAN/TILT button on the corresponding channels in the CAMERA menu, then the PAN/TILT window will be

Stand-alone DVR Instruction Manual 96▫ Pan/Tilt Vendor select Click the “PAN/TILT” button in the PAN/TILT window, then the vendor lists will show

7. Setup 97 ▫ Baud rate Click the “BAUD RATE” button in the PAN/TILT window and choose a value among 1200bps, 2400bps, 4800bps, 9600bps, 19200bps,

Stand-alone DVR Instruction Manual 98▫ Stop Bits Click the “STOP BITS” button in the PAN/TILT window and select 1 or 2 on the Stop Bits pop-up windo

7. Setup 99 7-4.6 Display ▫ Click the DISPLAY button in the CAMERA menu and select the ON or OFF. If the “ON” is selected, the camera name (camera